| |
|
|
|
|
|
|
| |
 |
|
 |
|
 |
|
| |
|
|
|
|
|
|
| |
First spray surface using soap free cleaning liquid. We use 50% alcohol 50% water mixture. Be sure to clean under the rubber edges & plastic fenders. |
|
You don’t need to do this step, but it helps to give you an idea of layout and position of graphics. Cut out & tape all the pieces in place.
|
|
It is best to make a mark with an eraseable pencil or pen like this. |
|
| |
|
|
|
|
|
|
| |
 |
|
 |
|
 |
|
| |
|
|
|
|
|
|
| |
Make a second mark on the other edge of the graphics like this. |
|
Pull backing paper down and behind the graphics. |
|
|
|
| |
|
|
Like this. |
|
| |
|
|
|
|
|
| |
|
|
|
|
|
|
| |
 |
|
 |
|
 |
|
| |
|
|
|
|
|
|
| |
Stick the graphics back down on the surface on while aligning your marks. |
|
Remove the backing paper as you squeegee the graphics. Next remove the paper backing on the horizontal side. Squeegee from center back while aligning with your marks. |
|
Remove application tape and rub down any graphic that may not be adhered to body. |
|
| |
|
|
|
|
|
| |
|
|
|
|
|
|
| |
 |
|
 |
|
 |
|
| |
|
|
|
|
|
|
| |
Now lets start the front finder. Make marks on 2 edges with an eraseable pen or pencil. Like here! . |
|
And here!
|
|
Pull backing paper and align with mark and apply graphic. |
|
| |
|
|
|
|
|
|
| |
 |
|
 |
|
 |
|
| |
|
|
|
|
|
|
| |
Squeegee to the front and to the back making sure that you graphic is aligned with your marks. |
|
Hold the bottom of the graphic out squeegee down back and forth until you get to the bottom. |
|
On some body styles you might need to use edge of squeegee to get graphic down into the bottom edge of body, so you will have a guide to cut off the graphic. |
|
| |
|
|
|
|
|
|
| |
 |
|
 |
|
 |
|
| |
|
|
|
|
|
|
| |
Like this. |
|
Use a knife to cut off excess graphics. |
|
Like this! |
|
| |
|
|
|
|
|
|
| |
 |
|
 |
|
 |
|
| |
|
|
|
|
|
|
| |
Now lets apply the upper fender. You will need to make marks again and align the graphic to them. Squeegee the leading edge. |
|
Check and make sure that the graphic is going to lay down correctly before you apply it. |
|
Hold the graphic up with one hand and squeegee the graphic back and forth to center. |
|
| |
|
|
|
|
|
|
| |
 |
|
 |
|
 |
|
| |
|
|
|
|
|
|
| |
Keep slight pressure on the graphic to help apply and reduce the chances of wrinkles. |
|
Align the upper fender strip to the upper fender you just applied. |
|
Squeegee over the edge and back down on the other side. |
|
| |
|
|
|
|
|
|
| |
 |
|
 |
|
 |
|
| |
|
|
|
|
|
|
| |
Now the hood. First make marks center, left & right corners. Double check the alignment because the hood does not have a straight edge. |
|
Pull the backing paper back about 3 inches. |
|
Align the graphic to the marks you made. |
|
| |
|
|
|
|
|
|
| |
 |
|
 |
|
 |
|
| |
|
|
|
|
|
|
| |
Squeegee the graphic left & right while pulling slightly down on the graphic. Make sure the graphic is laying down flat. The graphic can not have any extra slack on the left and right sides. You might need to pull the graphic up and start over if it is not laying down correctly. |
|
Pull the backing paper down a little bit at a time. |
|
Keep the graphic even and pull slightly down while squeegeeing. |
|
| |
|
|
|
|
|
|
| |
 |
|
 |
|
 |
|
| |
|
|
|
|
|
|
| |
Align the first strip on the hood. |
|
Squeegee from the center out. |
|
Now Align the next piece of the hood by pulling backing paper down just enough to apply the leading edge. |
|
| |
|
|
|
|
|
|
| |
 |
|
 |
|
 |
|
| |
|
|
|
|
|
|
| |
Squeegee from the center out to the corners. |
|
Now remove the hood to finish the last edge. |
|
Half way done. Now you need to start on the other side before you install the hoods center piece. Repeat steps 3 thru 24 for the other side. |
|
| |
|
|
|
|
|
|
| |
 |
|
 |
|
 |
|
| |
|
|
|
|
|
|
| |
Align the hoods center piece and make marks. |
|
Pull the paper backing from the top about an inch. Align with marks & squeegee down. |
|
Finished! Nice!
|
|
| |
|
|
|
|
|
|
